w***w
发帖数: 1552 | 1 3021 Speaker Stand - Silver (SS-01)
2749 16AWG Enhanced Loud Oxygen-Free Copper Speaker Wire Cable - 50ft
3992 High Speed HDMI 1.3a Category 2 Certified Cable
2801 1 PAIR OF High-Quality Copper Speaker Banana Plugs - Closed Screw
Type
2681 3ft High-quality Coaxial Audio/Video RCA CL2 Rated Cable M/M RG6U
75oh
m
2680 6ft High-quality Coaxial Audio/Video RCA CL2 Rated Cable - RG6/U
75ohm
5975 1 PAIR OF High-Quality Copper (non-banana) Speaker Plugs - Pin Screw
T
ype |
|
f*******e
发帖数: 8974 | 2 这个我不懂啊，当年买了几个，应该是闭口的
好像开口的线和plug垂直，是插进那个洞里然后用screw压紧，比较容易做
闭口的线和plug平行，顺着插进去冒个头然后用screw套在外面压紧
是不是根据功放后面的空间和个人口味来选的？ |
|
f*******e
发帖数: 8974 | 3 闭口的线是弯过来一点展开套在screw头上压紧的，接触没问题。
spade就是个叉子，你把音响接线柱那个冒拧出来一些，然后把叉子塞进冒下面再拧紧
冒就行了，我觉得比香蕉头稳当接触好，所以才用它。
装线的话和闭口的banana plug很像，那个叉子头可以拧下来，其他就和闭口香蕉头一
样了。
body两侧的两个小screw是额外的固定线的东西。拿到手很容易想出来怎么用的，呵呵
。就是记得最好不要把两个小螺丝完全卸下来，拧出来一些可以把线通过那个body就行
了。
我是通过body的部分全是裸线，至少和两个小螺丝接触的地方是裸的，增加接触，但是
我不知道对不对，呵呵。 |
|
d*****d
发帖数: 10658 | 4 多谢,如果没有大牛指点,我们hifi新人要走很多弯路啊.
刚才看了关于banana接头的介绍,原来这小东西也有那么多种类.买two pairs的closed
screw type接receiver,和two pairs的pin screw type接BS41可以吗? |
|
v*********n
发帖数: 1 | 5 就是relax，进行轻松愉快的conversation，让他们感觉到无论什么情况下你都能
handle stress。
其实case做的人和人差别不会特别大，尤其是final round（除非你很明显的screw up
）。关键是面试管
喜不喜欢你。
面了5个公司，越来越上手，拿到management consulting top3的offer，前两个非常严重的screw up。第一个太
desperate，太紧张，over
confident；第二个太谦虚显的没信心。后来想就干脆破罐子破摔不想那么多了，放开
了面试offer一个个就来了。
详细的回帖写吧，如果有人问 |
|
h***r
发帖数: 184 | 6 Just say no if you don't feel right. What I learned from workplace politics
is that always put your own interests (and feelings) ahead of your employers
' and colleagues'. Don't be afraid of screwing them, cuz they'll screw you
without any hesitation if they need to. There are no real good friends at
workplace.
Be tough and be smart. I learned this in a hard way.
PARTY, |
|
m*********g
发帖数: 1 | 7 It might be pretty upset for screwing up a phone interview. However, there
is something more important that you did not screw up like the work you did
earlier and those tech and ideas you treasure for such a long time. Lie down
and tell yourself at least your work is appealing to industry. That is
actually a lot, to most of "qianlao" at lab. Agree? |
|
m*********2
发帖数: 701 | 8 re: company recruiters are scumbags.
Then there are other kind of HRs.
1) Headhunters: these are your friends. Just ask them how to get into
the company and they will tell you. They will even help you do the
interviews if they can. (why? because they get paid if they place you.
aka, you are their boss)
2) Contractors: these are in between. (e.g. Microsoft's HRs). Their
purpose is to renew their contracts next year. So, they make sure
everyone is decent. They want to bring it good people so they ... 阅读全帖 |
|
H*******g
发帖数: 6997 | 9 senior screws? or even better senior screw drivers? well, I do see a whole
bunch of them. It might be your definition for developer, but not mine. |
|
s*******5
发帖数: 58 | 10 I just screwed one last week, me and that Indian interviewer both made
efforts to screw it.
But why sad? Feeling sad is only harmful to my health, not to his. |
|
f**********r
发帖数: 18251 | 11 【 以下文字转载自 Military 讨论区 】
发信人: kayaker2 (霜晨の月), 信区: Military
标 题: Re: 从job版和三藩版得来的印象，国人对老印已经投降了。 (转载)
发信站: BBS 未名空间站 (Sat Oct 12 10:52:41 2013, 美东)
没有党的领导，臭老九靠screw themselves harder to get ahead的老办法，已经不行
了。
以前老中臭垃圾，总是以自己能screw him/herself harder为荣。 米国人博士毕业发3
篇journal, 老中发8篇。 然后就得意洋洋的等着洋大人夸奖，赏饭。
现在木有用了，哈哈。
不过还有格蕾丝高的倒贴嫖资卖淫阿三路线可以借鉴。 |
|
S**I
发帖数: 15689 | 12 1. You're screwed; but if you can get H-1B approved even if you didn't get
your PhD, you're OK.
2. Same as above: you're screwed, go back to China is probably the only
option you have.
stem |
|
o**********e
发帖数: 18403 | 13
s
it'
很多行业很小。一张嘴就
够blacklist了。 有的行业
很大，有很多小型blacklist.
你不会知道。
你做了就做了。 不是什么
大事。 有没有后果你自己慢慢体会。
自杀人品也许人品还死不了呢，
也许人品死了，还不自知。
我没有责难的意思。 但是
你过来人也不要误导别人，鼓励
别人可以选择的时候去
自杀人品。
business 不是见利忘义的excuse.
There exist some company somewhere that
screwed somebody, that's no excuse
for you to screw someone else with
no provocation. |
|
o**********e
发帖数: 18403 | 14
s
it'
很多行业很小。一张嘴就
够blacklist了。 有的行业
很大，有很多小型blacklist.
你不会知道。
你做了就做了。 不是什么
大事。 有没有后果你自己慢慢体会。
自杀人品也许人品还死不了呢，
也许人品死了，还不自知。
我没有责难的意思。 但是
你过来人也不要误导别人，鼓励
别人可以选择的时候去
自杀人品。
business 不是见利忘义的excuse.
There exist some company somewhere that
screwed somebody, that's no excuse
for you to screw someone else with
no provocation. |
|
z****0
发帖数: 4413 | 15 【 以下文字转载自 Military 讨论区 】
发信人: sanguan (不限), 信区: Military
标 题: "性"格决定命运 -- 浅谈阿三跟黄皮索南的境况差异
发信站: BBS 未名空间站 (Sat Sep 19 12:21:19 2015, 美东)
人云: 性格决定命运. 美国的黄皮索南经常对阿三表现出强烈的羡慕嫉妒恨, 可见阿三
在美国普遍比黄皮索南要高一个或者多个等级, 抛去意识形态(比如美印关系美中关系以
及黄皮多自恨老将)的因素, 有必要从性格分析一下差异在哪里.
阿三的"性格"是什么, 索南都知道, 轮奸.索南的“性”格呢？ 撸管。 不要小看这个“
性”格， 反映的是多方位差异。
第一， 轮奸说明阿三有团队精神。 team work, 外国人选人进公司以及提拔人，对这个
很重视。 独乐乐不如众乐乐， 索南的独撸被阿三的轮奸甩开一万光年。
第二， 轮奸说明阿三有 can do attitude, 阿三们敢想敢干， 反观索南， 看到大白妞
有贼心没贼胆， 偷偷摸摸地回地下室撸管， 这样怎么能得到上司的重视。
第三， 美国的政界商界， 基本上就看你能不能玩人，... 阅读全帖 |
|
g*******2
发帖数: 8 | 16 Do NOT work for consulting companies!!! They're all liers and crooks!!
Search for "desi consulting", you'll see 1000+ of people got screwed by
those blood sucking leeches.
They'll force you to sign a contract later, basically signing your life away
serf. If you want to leave, they'll harrass you, suit you for a huge amount
of money, and/or try to screw your visa etc. They are bad people who do
nasty things. Especially be careful about consulting companies in NJ area. |
|
g*******2
发帖数: 8 | 17 Do NOT work for consulting companies!!! They're all liers and crooks!!
Search for "desi consulting", you'll see 1000+ of people got screwed by
those blood sucking leeches.
They'll force you to sign a contract later, basically signing your life away
serf. If you want to leave, they'll harrass you, suit you for a huge amount
of money, and/or try to screw your visa etc. They are bad people who do
nasty things. Especially be careful about consulting companies in NJ area. |
|
b*******e
发帖数: 67 | 18 ? you mean "plaster"?
有人也管drywall board叫plaster board，but传统的做法是3 coats plaster on
lathing代替drywall board,那种是湿着糊上去的，干了以后像水泥一样结实，你钉钉子
吃的住劲，drywall board把外面的纸斯开里面都是粉，所以挂重的东东不成...
screw因为上面有罗纹，磨擦力比光的nail更强，但drywall本身吃不住劲,所以
你要透过drywall钉到有stud的地方,I think either screw & large nail works on
drywall(remember drywall is 5/8" or 1/2" thick, so small nail can't get
through...) |
|
a***e
发帖数: 188 | 19 Don't worry. I had the similar experience when the contractor changed my roof
(including plywood sheathing). The contractor broke the ceiling in my master
bedroom. I saw how he repaired it. Basically, you need to take down the whole
4x8 drywall off and replace it with a new one. You need to use drywall screw
to screw the drywall on the wood frame, then use some drywall tape to seal,
then you need to apply plaster. I remember the contractor came 3 times because
he had to wait until the previous c |
|
a***e
发帖数: 188 | 20 Don't worry. I had the similar experience when the contractor changed my roof
(including plywood sheathing). The contractor broke the ceiling in my master
bedroom. I saw how he repaired it. Basically, you need to take down the whole
4x8 drywall off and replace it with a new one. You need to use drywall screw
to screw the drywall on the wood frame, then use some drywall tape to seal,
then you need to apply plaster. I remember the contractor came 3 times because
he had to wait until the previous c... 阅读全帖 |
|
w*****o
发帖数: 421 | 21 bought Z, but it's a pain in the neck to install it, sigh. couldn't hire
anyone to install either (you have to buy it from them). If you are not a
handy man, stay away from Z :(
Our kitchen already vented out, all we have to do is to put the Z back to
its place, but the manual is so bad, no information on how to use the screws
and the locations of screws are so hard to reach. Anyone can offer some
comments? Try to find old posts but not so helpful :( |
|
t*****m
发帖数: 254 | 22 I DIYed solid-hardwood floor on concrete, taking a bit effort.
Here is how I did it.
1. Glue down 1/2" plywood on conrete;
2. Further secure the 1/2" plywood using conrete screws (drill holes on
concrete first, this took the most time, plywood has tension and glue may
fail over time, these conrete screws maybe the only thing to hold down the
floor eventually);
3. Put down felt-paper on plywood to keep moisture down;
4. Nail solid-hardwood floor onto plywood.
I |
|
p**f
发帖数: 2610 | 23 做那么几根framing,还买个compressor和gun,几百块,估计以后再也不用的.意思不大啊.
我建议还是pre drill,然后screw.
framing gun是Professional用的,人家一天把一层的framing都做了,射５００－１００
０个钉
子,用screw就贵多了.
而且老三有兔兔,gun危险,走火伤了兔兔可就不好了. |
|
k**u
发帖数: 10502 | 24 是不是降低了GDP？
刚刚裁了一片不锈钢，给断掉的淋浴头架子补上了。
使用的工具及材料计有：air cutter, table grinder, angle grinder, Dremel,drill
，hammer，glue, metal screw, table vise, screw driver, claps,等等。工程质量
自评C+，费时两小时，省钱20块。 |
|
p**f
发帖数: 2610 | 25 同意,必须换长screw,门框至少有两个studs,3-4"左右screw没问题. |
|
h******2
发帖数: 102 | 26 the drillspot one was exactly the same as Lowes's (brian brand). I believe
it was made of aluminmum.
There were 4 screw holes on the flashing so you can use screws and then seal
with silicone and/or Great Stuff |
|
R**R
发帖数: 3318 | 27 "deck screws" are very good screes.strong.
They come with screw bit. |
|
b********r
发帖数: 59 | 28 Here is what I found from manual. Good to know :D
The torque adjustment collar shown in Fig. 5 has 24 settings. There are 23
screwdriving settings and a drilling setting which is represented by the
drill bit symbol. For screwdriving proceed
as follows:
Set the torque adjustment to position “1”. Fit and tighten the first screw
. If the clutch of your drill starts to ratchet before the screw is
correctly seated, rotate the adjustment collar as necessary, until the
clutch slips when the head of th |
|
R**R
发帖数: 3318 | 29 看来大家对系列秀10 的Snow plow是很不敢冒，上座率太低。一些老观众也没了。
没关系，要不好，你就砸。我这类停播，换别的。
这次咱室外做Deck. 再不好，室内装书房。实在不行，咱停播了，改行上别处混去。
所谓乡村版Deck： 大，粗旷，做工不要求很细。（相对 现代版而言,后续）
工序：
1， 申请 permit. Flowing the permit instruction, building code.
2, 挖柱基，地下3尺。Wait for footing inspection.
3,灌水泥，固定柱子。加 header 到墙上，加大梁（double beam）到柱子上，加小梁
从header to 大梁。图1， 图2. Wait for structure inspection.
4， 加面板。 要整根的，用 3” Deck screw 从下往上固定。Make sure no visible
screw.
5，加护栏，加楼梯。图3， 图4. Wait for final inspection.
6，Party. 图5.
欢迎大家讨论细节。 |
|
b********e
发帖数: 1946 | 30 4， 加面板。 要整根的，用 3” Deck screw 从下往上固定。Make sure no visible
screw.
这个"从下往上固定"要赞. 为了美观,多费不少事呀.
visible |
|
g*****9
发帖数: 4125 | 31 i can see the part that is connected to the floating ball, if there is screw
, you can turn the screw, if not, carefully bend the rod a little (be
careful not to break it, it looks kind of old) try to raise the water level
just below the over flow pipe. If everything fails, you will just have to
hold down the handle until all the water come out for right now, and we can
continue our trouble shooting. |
|
g*****9
发帖数: 4125 | 32 My suggestion would be to take the door off its hinges, go to your local
glass company and buy a tube of mirror adheasive, lay the door down
somewhere out of the way and glue the mirror to the door look at the
instructions on the tube for the cure time, when dry rehang the door, then
you will have no problem with the mirror, but a word of caution make sure
the door will take the weight check the hinges and the screw fixings in the
hinges if nessesary use longer screws in the hinges so they bite |
|
s**********d
发帖数: 36899 | 33 我想应该这样：断裂处前后钻通孔，靠表面大一些，上bolt/nut，
然后用腻子盖住涂上相似的漆。
或者直接用screw，合适的地方钻浅孔用于埋头和深的pilot hole
到断裂处，用screw拧上摸腻子上漆。可以多拧几个。 |
|
g*****9
发帖数: 4125 | 34 You don't need the impact driver unless you plan to work on cars alot and
drive screw into very hard material.
One good thing, it will be harder to strip screw with this. |
|
o*********8
发帖数: 488 | 35 LZ sounds very professional --- can you give me a picture link of a blade
screw driver? I searched online and didn't find one. Also, can I just use
a common knife? I searched for "utility knife" on the internet and it
doesn't seem to be different from a common knife.
screw |
|
p*********s
发帖数: 55 | 36 nail probably will solve the problem for a while but not for very long -
drill a hole first, then drill a bigger hole 3mm deep(same size as your
screw head) then scew in a proper size screw, then use wood putty to hide
the head. |
|
w*******g
发帖数: 9932 | 37 Ultimately the responsibility is with AA. AA screwed up. It screwed
customers royally over this fiasco. It can't blame Beijing airport while
telling customers
to fuck themselves. |
|
g********3
发帖数: 1281 | 38 Can you try to screw in two more screws using the other 2 holes? |
|
b***y
发帖数: 405 | 39 腿跟床框的连接用的是Lag screw吗？
这个地方吃劲很大，用Lag screw松的快而且每次拧紧都伤木头。用Bolt-nut pair比较
合适。
床板上睡人后会很重，从图片上看你用小螺丝联到床框上，可能还有床柱上。我觉得不
结实。
床板要么就直接座在短桩上，要么用卯榫或者Bolt-nut pair连腿上。 |
|
s******8
发帖数: 4192 | 40 不要大screw，要长的，比如主要结构用4寸，细节用2寸。pre-drill，否则木头可能会
裂开。当然screw成本比nail高很多很多。 |
|
m***y
发帖数: 14763 | 41 drywall 上面好多nail pops? Should use screws on drywalls.
Anyway, nobody born handy. Now it's your time to rise and shine! Start with
screwing back the uneven drywalls. |
|
s********s
发帖数: 3945 | 42 Good job!!!
spent a lot of time comparing the prices between lumber stores. Should have
saved $800 if having the boards ordered from HD, but their boards are
usually BAD.)
% off coupon).
for only $200. Another $100 was for about 1000 ordinary 3.5" treated wood
screws.)
also need power tools (better cordless) like drills/drivers, a circular saw,
and a digger, a post level, a long tape measure, a wheel barrel, etc.
builds a more sturdy fence. It will also be easier to repair when needed.
with the... 阅读全帖 |
|
s******g
发帖数: 2318 | 43 270ft all by yourself, man really nice job, really handy, super zan
Here's the price I quote from some fence company in central NJ, share with
all guys:
#1) 6’ high Solid Straight Top, Dog-Eared Fence: Custom built on site w/
100% Cedar 1x6” boards & Stainless steel nails to prevent bleeding. 4x4”
flat top posts are set 32” deep in concrete footings:
@$27.95 per lf, single gates are $395.00
#2) 6’ high Solid Capped Cedar Board Fence w/ Nantucket Post Caps: Also
custom built on site... 阅读全帖 |
|
h********8
发帖数: 7355 | 44 这倒是，俺干活慢，尤其在铁皮上打screw，钻头／screw bit holder来回换，挺烦的。 |
|
l*****o
发帖数: 26631 | 45 1. 用榫头, 很需要技术。。。
2. toe nail/screw，或者类似的pocket hole screw/handrail bolts 好像也很需要技
术。。。
3. 用专门的railing connector或者一般的bracket/joint hanger, 似乎用起来比较简
单，不过有点丑
怎么办啊？ 像我这种不会木工的人是不是还是用第三种比较好？ |
|
d******i
发帖数: 7160 | 46 找了几个link,比如
http://www.partselect.com/refrigerator+freezer-is-warm+repair.h
都说用试电笔量电阻。
偶就拆开了冷藏室顶端的控制盒。看见了如图的景象。
我没法判断哪个是Drefrost Timer,哪个是ThermoStat.
因为据说timer有四个线头，而唯一四个线头的是图中贴绿签的那个插头，而这四条线
中哪个也不是白线，也没有标着‘3’或‘C’。不过俺还是拿电笔量了电阻。结果总是
最下面粉色的与其他任何线头之间是断路(Infinity),其他两两间都是‘0’！
而且我也没有找到任何的'screw'能让我旋转(据说这screw在defrostTimer上)，只能转
timerSwitch(“Find your refrigerator's timer switch and turn it in a
clockwise motion until it clicks. Use your multitester and test the
terminals again in the same manner as in... 阅读全帖 |
|
h********8
发帖数: 7355 | 47 ４X８的，当时不知道有这种顶的东东。俺先打４个screws，然后喘半天，再接着打
screws ：） |
|
p**5
发帖数: 2544 | 48 能否请教一下，dry wall screw和blind自带的screw有什么区别？ |
|
z*****z
发帖数: 2438 | 49 blind自带screw后面的十字槽浅，材料软，螺距小，拧的时候改锥容易打滑，而且需要
很大的力压住。拧得圈数也多。
简而言之，自带screw质量太次，不好拧。 |
|
l*****o
发帖数: 26631 | 50 要把sill plate钉到水泥上面，我看网上一般都是一根2x4的sill plate。
问题是我家怎么有两根叠在一起，底下一根2x6的，上面一根2x4的。
2x6的我用lag shield和lag screw固定到水泥上面可以吗？还是用concrete screw比较
好？
2x4的是不是只要固定在2x6的上面就可以了，还是需要用超级长的螺丝钉一起钉在水泥
地上？
多谢多谢。 |
|
