|
|---|
|
|
|
|
|
|
z****i
发帖数: 1174 | 1 要那种比较有private的fence,就是拦起来看不见里面院子的。
哪里便宜啊？ 把后院全围起来大概花多少钱搞定？ | B***r
发帖数: 534 | | z****i
发帖数: 1174 | | t****e
发帖数: 72 | 4 我是从网上买的vinyl的。先在local vendor的店里看过样品，觉得比HD/Lowes的质量
好很多。6'x8'section 不到100， 9' post 不到 30.
客服似乎还可以，回应很快，而且把shipping也给我免了。
为避免做广告嫌疑就不说具体的网站了，愿意进一步交流的可以在俱乐部里聊聊。
【在 B***r 的大作中提到】
: 同问！
: Home Depot就有，下面两个是木头的，
: http://www.homedepot.com/Outdoors-Fencing-Wood/h_d1/N-5yc1vZbb2
: http://www.homedepot.com/Outdoors-Fencing-Wood/h_d1/N-5yc1vZbb2
: 这个是Vinyl的
: http://www.homedepot.com/Building-Materials-Fencing-Vinyl-Panel
: 去店里看过，不太好看，而且HD的东西一般不算便宜，也想知道哪里还有卖的。
| B***r
发帖数: 534 | 5 到HD网站上search fence就能看到，第一个$23.97，第二个$24.97(不过是42"的，有点
矮)。
【在 z****i 的大作中提到】
: 那2个木头的不错啊，怎么看不见价钱？
| z****i
发帖数: 1174 | 6 妈妈呀，那90*150的后院，就按第一个（6*8）算下来，围3面，岂不是得花个1000刀！
【在 B***r 的大作中提到】
: 到HD网站上search fence就能看到，第一个$23.97，第二个$24.97(不过是42"的，有点
: 矮)。
| l*****o
发帖数: 26631 | 7 加上人工费要double吧
【在 z****i 的大作中提到】
: 妈妈呀，那90*150的后院，就按第一个（6*8）算下来，围3面，岂不是得花个1000刀！
| z****i
发帖数: 1174 | 8 ft...
不免费安呐？？装个篱笆都这么多钱，我撞墙去算了
安过fence的同学院部愿意过来说一下你们一共花多少钱整这个？多谢了！
另外fence自己装简单吗？能自己干还是自己干吧哎！
【在 l*****o 的大作中提到】
: 加上人工费要double吧
| C**K
发帖数: 3672 | 9 which one? 我也在看vinyl的.
您自己裝嗎?
【在 t****e 的大作中提到】
: 我是从网上买的vinyl的。先在local vendor的店里看过样品，觉得比HD/Lowes的质量
: 好很多。6'x8'section 不到100， 9' post 不到 30.
: 客服似乎还可以，回应很快，而且把shipping也给我免了。
: 为避免做广告嫌疑就不说具体的网站了，愿意进一步交流的可以在俱乐部里聊聊。
| l*****o
发帖数: 26631 | 10 咳咳， fence本来就是很贵的么。
尤其是大的院子，买房子的时候都可以算到房价里去的。
自己安是可以的，挖坑，放柱子，浇水泥，再把柱子之间的板都连上。
主要是挖坑很累，可以租一个挖坑的机器。
【在 z****i 的大作中提到】
: ft...
: 不免费安呐？？装个篱笆都这么多钱，我撞墙去算了
: 安过fence的同学院部愿意过来说一下你们一共花多少钱整这个？多谢了！
: 另外fence自己装简单吗？能自己干还是自己干吧哎！
| | | h***b
发帖数: 1233 | | B***r
发帖数: 534 | 12 自己装估计挺累的，还要浇水泥呢。问过handyman,$40/panel已经算很便宜的了。
【在 z****i 的大作中提到】
: ft...
: 不免费安呐？？装个篱笆都这么多钱，我撞墙去算了
: 安过fence的同学院部愿意过来说一下你们一共花多少钱整这个？多谢了！
: 另外fence自己装简单吗？能自己干还是自己干吧哎！
| j***b
发帖数: 5901 | 13 第一个是$23.97/ft?
【在 B***r 的大作中提到】
: 到HD网站上search fence就能看到，第一个$23.97，第二个$24.97(不过是42"的，有点
: 矮)。
| E********l
发帖数: 48 | 14 you'd better not buy stock wood material.
the material suitable for fence is either treated wood or cedar. | c**t
发帖数: 16 | 15 请您告诉我是那家店，好吗？非常感谢。也要装啦
【在 t****e 的大作中提到】
: 我是从网上买的vinyl的。先在local vendor的店里看过样品，觉得比HD/Lowes的质量
: 好很多。6'x8'section 不到100， 9' post 不到 30.
: 客服似乎还可以，回应很快，而且把shipping也给我免了。
: 为避免做广告嫌疑就不说具体的网站了，愿意进一步交流的可以在俱乐部里聊聊。
| c********7
发帖数: 739 | 16 我们家装的6'高的vinyl,一共大概240feet，两个门，一共$8500.找hd的人装的。hd
fence是外包给一个公司的，从那里订的材料比我们在hd店里看到的要结实。差不多是
工料对半
这个活自己干不容易，打post要挖比较深的洞，再灌水泥，挺累的
【在 z****i 的大作中提到】
: ft...
: 不免费安呐？？装个篱笆都这么多钱，我撞墙去算了
: 安过fence的同学院部愿意过来说一下你们一共花多少钱整这个？多谢了！
: 另外fence自己装简单吗？能自己干还是自己干吧哎！
| G*H
发帖数: 624 | 17 You think $1,000 is too much? Just on the contrary, $1,000 is too far away
from the actual cost for 90x2+150=330 feet of 6' wood fence. The cost for
only the material of the worst quality (treated boards, treated posts/rails,
low quality concrete mix...) will easily be over $2000.
【在 z****i 的大作中提到】
: 妈妈呀，那90*150的后院，就按第一个（6*8）算下来，围3面，岂不是得花个1000刀！
| j***b
发帖数: 5901 | 18 Low quality concrete mix is fine. It's not like you can see a difference,
and any kind of concrete mix should be strong enough for just fence.
rails,
【在 G*H 的大作中提到】
: You think $1,000 is too much? Just on the contrary, $1,000 is too far away
: from the actual cost for 90x2+150=330 feet of 6' wood fence. The cost for
: only the material of the worst quality (treated boards, treated posts/rails,
: low quality concrete mix...) will easily be over $2000.
| r******0
发帖数: 2753 | 19 你肯定算错了，哪能那么便宜。你要的还是要有privacy的那种，那panel，post还有门，所有加一起，光材料（就算用最便宜的）三千肯定打不住，四千都玄。
才想明白，原来你是把per ft看成了per panel，那你的价钱得乘８了。
【在 z****i 的大作中提到】
: 妈妈呀，那90*150的后院，就按第一个（6*8）算下来，围3面，岂不是得花个1000刀！
| G*H
发帖数: 624 | 20 I installed 270 feet cedar fence myself. These are what I paid for:
(1). $2,300 for 600 1"x6"x6' western red cedar boards plus delivery. (I spent a lot of time comparing the prices between lumber stores. Should have saved $800 if having the boards ordered from HD, but their boards are usually BAD.)
(2). $1,300 for posts/rails/concrete mix/delivery from lowes. (Used the 10% off coupon).
(3). $180 for renting a dingo to dig the holes.
(4). about $300 for screws. (Bought 4000 2"(8d) stainless screws from ebay for only $200. Another $100 was for about 1000 ordinary 3.5" treated wood screws.)
All these cost an amount a little over $4,000. Please note that you will also need power tools (better cordless) like drills/drivers, a circular saw, and a digger, a post level, a long tape measure, a wheel barrel, etc.
Using screws rather than nails increases the amount of labor a lot, but it builds a more sturdy fence. It will also be easier to repair when needed.
In total, here are the pros and cons.
Pros: I saved over $4000 by DIY. The most important is that, comparing with the made-by-contractor fences, my fence is much stronger.
Cons: it took me over two weeks to finish the work, and it was the heaviest labor I had never done before. After drilling nearly 5000 holes and driving in the same number of screws, my fingers were painful and it lasted for two weeks.
Overall, from a monetary point of view, it is not worth your time/effort to DIY. Nevertheless, considering that most contractors bury your posts only 2ft (or even under) into the soil with little concrete, you can make a piece of stronger fence by DIY.
【在 z****i 的大作中提到】
: ft...
: 不免费安呐？？装个篱笆都这么多钱，我撞墙去算了
: 安过fence的同学院部愿意过来说一下你们一共花多少钱整这个？多谢了！
: 另外fence自己装简单吗？能自己干还是自己干吧哎！
| | | j***b
发帖数: 5901 | 21 没有必要用screw钉fence board。board就算钉子脱出来也很容易修，就是几锤子的事情。把rail用screw钉在post上就行了。特别是有ringed shaft的钉子，也不容易脱的。用钉子省工太多了。
spent a lot of time comparing the prices between lumber stores. Should have
saved $800 if having the boards ordered from HD, but their boards are
usually BAD.)
% off coupon).
for only $200. Another $100 was for about 1000 ordinary 3.5" treated wood
screws.)
also need power tools (better cordless) like drills/drivers, a circular saw,
and a digger, a post level, a long tape measure, a wheel barrel, etc.
builds a more sturdy fence. It will also be easier to repair when needed.
with the made-by-contractor fences, my fence is much stronger.
heaviest labor I had never done before. After drilling nearly 5000 holes and
driving in the same number of screws, my fingers were painful and it lasted
for two weeks.
【在 G*H 的大作中提到】
: I installed 270 feet cedar fence myself. These are what I paid for:
: (1). $2,300 for 600 1"x6"x6' western red cedar boards plus delivery. (I spent a lot of time comparing the prices between lumber stores. Should have saved $800 if having the boards ordered from HD, but their boards are usually BAD.)
: (2). $1,300 for posts/rails/concrete mix/delivery from lowes. (Used the 10% off coupon).
: (3). $180 for renting a dingo to dig the holes.
: (4). about $300 for screws. (Bought 4000 2"(8d) stainless screws from ebay for only $200. Another $100 was for about 1000 ordinary 3.5" treated wood screws.)
: All these cost an amount a little over $4,000. Please note that you will also need power tools (better cordless) like drills/drivers, a circular saw, and a digger, a post level, a long tape measure, a wheel barrel, etc.
: Using screws rather than nails increases the amount of labor a lot, but it builds a more sturdy fence. It will also be easier to repair when needed.
: In total, here are the pros and cons.
: Pros: I saved over $4000 by DIY. The most important is that, comparing with the made-by-contractor fences, my fence is much stronger.
: Cons: it took me over two weeks to finish the work, and it was the heaviest labor I had never done before. After drilling nearly 5000 holes and driving in the same number of screws, my fingers were painful and it lasted for two weeks.
| z****i
发帖数: 1174 | 22 我嘴都快张成0型了，我家lg一开始竟然估计五六百刀就解决的 | s********s
发帖数: 3945 | 23 Good job!!!
spent a lot of time comparing the prices between lumber stores. Should have
saved $800 if having the boards ordered from HD, but their boards are
usually BAD.)
% off coupon).
for only $200. Another $100 was for about 1000 ordinary 3.5" treated wood
screws.)
also need power tools (better cordless) like drills/drivers, a circular saw,
and a digger, a post level, a long tape measure, a wheel barrel, etc.
builds a more sturdy fence. It will also be easier to repair when needed.
with the made-by-contractor fences, my fence is much stronger.
heaviest labor I had never done before. After drilling nearly 5000 holes and
driving in the same number of screws, my fingers were painful and it lasted
for two weeks.
【在 G*H 的大作中提到】
: I installed 270 feet cedar fence myself. These are what I paid for:
: (1). $2,300 for 600 1"x6"x6' western red cedar boards plus delivery. (I spent a lot of time comparing the prices between lumber stores. Should have saved $800 if having the boards ordered from HD, but their boards are usually BAD.)
: (2). $1,300 for posts/rails/concrete mix/delivery from lowes. (Used the 10% off coupon).
: (3). $180 for renting a dingo to dig the holes.
: (4). about $300 for screws. (Bought 4000 2"(8d) stainless screws from ebay for only $200. Another $100 was for about 1000 ordinary 3.5" treated wood screws.)
: All these cost an amount a little over $4,000. Please note that you will also need power tools (better cordless) like drills/drivers, a circular saw, and a digger, a post level, a long tape measure, a wheel barrel, etc.
: Using screws rather than nails increases the amount of labor a lot, but it builds a more sturdy fence. It will also be easier to repair when needed.
: In total, here are the pros and cons.
: Pros: I saved over $4000 by DIY. The most important is that, comparing with the made-by-contractor fences, my fence is much stronger.
: Cons: it took me over two weeks to finish the work, and it was the heaviest labor I had never done before. After drilling nearly 5000 holes and driving in the same number of screws, my fingers were painful and it lasted for two weeks.
| s******g
发帖数: 2318 | 24 270ft all by yourself, man really nice job, really handy, super zan
Here's the price I quote from some fence company in central NJ, share with
all guys:
#1) 6’ high Solid Straight Top, Dog-Eared Fence: Custom built on site w/
100% Cedar 1x6” boards & Stainless steel nails to prevent bleeding. 4x4”
flat top posts are set 32” deep in concrete footings:
@$27.95 per lf, single gates are $395.00
#2) 6’ high Solid Capped Cedar Board Fence w/ Nantucket Post Caps: Also
custom built on site using 1x4” or 1x6” boards and a 1x4” top cap. 4x4”
flat top posts w/ Nantucket post Caps Set 32” deep in concrete – sections
are sandwiched between posts:
@$29.85 per lf & Gates are same
#3) 6’ high Straight Top, Dog-Eared Board on Board: Custom built neighbor
friendly fence (Same on both sides) Same 1x6” boards & 4x4” posts
@$28.95 per lf
#4) 6’ high White PVC by Country Estate, style: Carribean w/ New England
Post Caps. This fence is built with virgin PVC materials, 5x5” posts w/
New England Post caps set 32” deep in concrete. 50 year non pro-rated
Manufacturers warranty.
@$40.00 per lf & $485.00 per gate
#5) STAIN on Wood Fences: Approximately $8.95 per lf
so 270 feet easily cost you 7k-8k including labor....
spent a lot of time comparing the prices between lumber stores. Should have
saved $800 if having the boards ordered from HD, but their boards are
usually BAD.)
% off coupon).
for only $200. Another $100 was for about 1000 ordinary 3.5" treated wood
screws.)
also need power tools (better cordless) like drills/drivers, a circular saw,
and a digger, a post level, a long tape measure, a wheel barrel, etc.
builds a more sturdy fence. It will also be easier to repair when needed.
with the made-by-contractor fences, my fence is much stronger.
heaviest labor I had never done before. After drilling nearly 5000 holes and
driving in the same number of screws, my fingers were painful and it lasted
for two weeks.
【在 G*H 的大作中提到】
: I installed 270 feet cedar fence myself. These are what I paid for:
: (1). $2,300 for 600 1"x6"x6' western red cedar boards plus delivery. (I spent a lot of time comparing the prices between lumber stores. Should have saved $800 if having the boards ordered from HD, but their boards are usually BAD.)
: (2). $1,300 for posts/rails/concrete mix/delivery from lowes. (Used the 10% off coupon).
: (3). $180 for renting a dingo to dig the holes.
: (4). about $300 for screws. (Bought 4000 2"(8d) stainless screws from ebay for only $200. Another $100 was for about 1000 ordinary 3.5" treated wood screws.)
: All these cost an amount a little over $4,000. Please note that you will also need power tools (better cordless) like drills/drivers, a circular saw, and a digger, a post level, a long tape measure, a wheel barrel, etc.
: Using screws rather than nails increases the amount of labor a lot, but it builds a more sturdy fence. It will also be easier to repair when needed.
: In total, here are the pros and cons.
: Pros: I saved over $4000 by DIY. The most important is that, comparing with the made-by-contractor fences, my fence is much stronger.
: Cons: it took me over two weeks to finish the work, and it was the heaviest labor I had never done before. After drilling nearly 5000 holes and driving in the same number of screws, my fingers were painful and it lasted for two weeks.
| j***b
发帖数: 5901 | 25 我个人认为用ceder也不比pt lamber强多少。ceder的主要好处是不容易弯曲。但是我的pt的也基本没怎么弯。另外就是ceder颜色好些。但是都会被太阳晒成灰色。不过ceder会晒成银灰色，比pt的乌灰色好看。但是pt的stain之后，哪怕是用solid的，也会比ceder的不stain好看。
总的来说我觉得我选pt很合算。我打算晒灰之后stain。
我的大概是250ft左右，pt lamber。最后所有开销（包括买工具的钱,一大两小三个门。总之是跟这个project沾边的都算了，出了汽油钱）是$2600左右。这个项目买的一些工具和材料后来又得到了广泛的利用。
”
sections
【在 s******g 的大作中提到】
: 270ft all by yourself, man really nice job, really handy, super zan
: Here's the price I quote from some fence company in central NJ, share with
: all guys:
: #1) 6’ high Solid Straight Top, Dog-Eared Fence: Custom built on site w/
: 100% Cedar 1x6” boards & Stainless steel nails to prevent bleeding. 4x4”
: flat top posts are set 32” deep in concrete footings:
: @$27.95 per lf, single gates are $395.00
: #2) 6’ high Solid Capped Cedar Board Fence w/ Nantucket Post Caps: Also
: custom built on site using 1x4” or 1x6” boards and a 1x4” top cap. 4x4”
: flat top posts w/ Nantucket post Caps Set 32” deep in concrete – sections
| C**K
发帖数: 3672 | 26 學習了, 我找的估價隨便打個價, 也沒說要挖多深, 4'x8'的picket竟要我$90一個....
我的名字拼錯, city也拼錯.
也強調virgin PVC, virgin PVC有什麼優點？
”
sections
【在 s******g 的大作中提到】
: 270ft all by yourself, man really nice job, really handy, super zan
: Here's the price I quote from some fence company in central NJ, share with
: all guys:
: #1) 6’ high Solid Straight Top, Dog-Eared Fence: Custom built on site w/
: 100% Cedar 1x6” boards & Stainless steel nails to prevent bleeding. 4x4”
: flat top posts are set 32” deep in concrete footings:
: @$27.95 per lf, single gates are $395.00
: #2) 6’ high Solid Capped Cedar Board Fence w/ Nantucket Post Caps: Also
: custom built on site using 1x4” or 1x6” boards and a 1x4” top cap. 4x4”
: flat top posts w/ Nantucket post Caps Set 32” deep in concrete – sections
| e*w
发帖数: 1185 | 27 Here is a quote I got from a fence company:
310 lf of black aluminum fence (4' tall) and three gates for about $6K, incl
uding material and labor. | x********g
发帖数: 268 | 28 fence本来就很贵，自己装吧，没啥技术。不要忘了先给那个“call before you dig“
打电话，否则挖到人家的cable，你吃不消。 | G*H
发帖数: 624 | 29 That's a great price!
incl
【在 e*w 的大作中提到】
: Here is a quote I got from a fence company:
: 310 lf of black aluminum fence (4' tall) and three gates for about $6K, incl
: uding material and labor.
| G*H
发帖数: 624 | 30 Agree with this--"没啥技术".
To those who want to do the fence themselves: Before you start, call your
county office to see if a permit is needed; call the gas, cable, and utility
companies to mark the underground pipes/lines within one week before you
dig the holes.
【在 x********g 的大作中提到】
: fence本来就很贵，自己装吧，没啥技术。不要忘了先给那个“call before you dig“
: 打电话，否则挖到人家的cable，你吃不消。
| | | H******7
发帖数: 34403 | 31 An "average" backyard fence of 200 linear feet costs about $2,500-
$3,000, with gates adding $100-$250 or more depending on size and style,
according to a Virginia construction company. Actual prices depend on
the type and height you choose, the total length and the number of
pedestrian/vehicle gates. Costs also vary considerably in rural and
urban areas, depending on the local economy.
with
w/
4x4”
Also
4x4”
sections
【在 s******g 的大作中提到】
: 270ft all by yourself, man really nice job, really handy, super zan
: Here's the price I quote from some fence company in central NJ, share with
: all guys:
: #1) 6’ high Solid Straight Top, Dog-Eared Fence: Custom built on site w/
: 100% Cedar 1x6” boards & Stainless steel nails to prevent bleeding. 4x4”
: flat top posts are set 32” deep in concrete footings:
: @$27.95 per lf, single gates are $395.00
: #2) 6’ high Solid Capped Cedar Board Fence w/ Nantucket Post Caps: Also
: custom built on site using 1x4” or 1x6” boards and a 1x4” top cap. 4x4”
: flat top posts w/ Nantucket post Caps Set 32” deep in concrete – sections
|
|
|
|
|
|
|
|
