a****o 发帖数: 133 | 1 号称
Install this valve and you can drain your engine oil without tools and
without mess. Just lift the lever of this solid brass ball valve and give it
a quarter turn to open it.
http://www.fumotousa.com/ |
l**********i 发帖数: 11748 | 2 一定要油热的时候放油
不然冷油太粘,放1个多小都放不干净 |
f****t 发帖数: 15913 | 3 别用,哪天车底盘碰上东西,那个阀门被打开,就悲剧了。
it
【在 a****o 的大作中提到】 : 号称 : Install this valve and you can drain your engine oil without tools and : without mess. Just lift the lever of this solid brass ball valve and give it : a quarter turn to open it. : http://www.fumotousa.com/
|
a******o 发帖数: 16625 | 4 没用过,但是看review,主要问题是放得太慢。
it
【在 a****o 的大作中提到】 : 号称 : Install this valve and you can drain your engine oil without tools and : without mess. Just lift the lever of this solid brass ball valve and give it : a quarter turn to open it. : http://www.fumotousa.com/
|
u****q 发帖数: 24345 | |
t*****g 发帖数: 7455 | 6 这个应该和机油标号有关系
【在 l**********i 的大作中提到】 : 一定要油热的时候放油 : 不然冷油太粘,放1个多小都放不干净
|
Y****a 发帖数: 17170 | 7
我也弄了一个准备装在outback上。
你的那个加了那个箍没?
主要是担心被石子啥的弹开了。
【在 u****q 的大作中提到】 : 我用在Forester上。很好用。没觉得慢。
|
c****1 发帖数: 2291 | 8 以前老车用的 很好
如果你是用非合成油 跑得又多 经常换油 可以装一个 |
|
u****q 发帖数: 24345 | 9 没加啥箍。Forester下面有塑料的shield。
【在 Y****a 的大作中提到】 : : 我也弄了一个准备装在outback上。 : 你的那个加了那个箍没? : 主要是担心被石子啥的弹开了。
|
Y****a 发帖数: 17170 | 10
这样啊, forester设计的不错呀。 outback好像没有这个东西
【在 u****q 的大作中提到】 : 没加啥箍。Forester下面有塑料的shield。
|
a****o 发帖数: 133 | 11 加的箍是不是"Hose Clip",在五金店都能买到?
【在 Y****a 的大作中提到】 : : 这样啊, forester设计的不错呀。 outback好像没有这个东西
|
Y****a 发帖数: 17170 | 12
https://www.qwikvalve.com/fumoto-l-clip.html
这个东西。
【在 a****o 的大作中提到】 : 加的箍是不是"Hose Clip",在五金店都能买到?
|
l**********i 发帖数: 11748 | 13 Mobile 1 全合成0W-30
冷的时候放了1个多小时,还在滴滴答答
油热时10分钟就干净了
【在 t*****g 的大作中提到】 : 这个应该和机油标号有关系
|