x****d 发帖数: 1766 | 1 我不是这方面专家。这个路还很长,不是说没具体方案。你去看commotion和zeromq吧
,看完你至少会得到些启发。其实还有很多方案,考虑家电上网春天还有几年,摩尔定
理推算,家电上有一个比现在手机强两三倍计算能力的东东不是很不靠谱吧?
让我用我懂的技术做,我都能做出来,用embendded的activeMQ都行。不就是messaging
么?
我家冰箱电视还要给中宣部发布信息?给cia,fbi监控? WTF! |
|
A****F 发帖数: 699 | 2 最近帮朋友设计加宽地基,准备用#5 bar,我本身不是做building的,请问top bar要伸
进去原有基础多深才能有足够的develope length fro #5 bar.
包子答谢。 |
|
j***h 发帖数: 4412 | 3 看来同学们太忙,偶就抽空灌壶水。相关规范是ACI 318-05 12.2.1 to 12.2.5:
12.2.1 — Development length for deformed bars and deformed wire in tension,
ld shall be determined from either 12.2.2 or 12.2.3, but shall not be less
than 12 in.
12.2.2 — For deformed bars or deformed wire, ld shall be as follows:
No. 6 and smaller bars and deformed
wires No. 7 and larger bars
Clear spacing of bars or wires
being developed or spliced fy*ψt*ψe*λ/(25*sqrt(fc′))db
|
|
A****F 发帖数: 699 | 4 thanks.
我决定打个洞把钢筋穿过去就没问题了。
tension,
less
|
|
|
|
w*******r 发帖数: 330 | 7 哈哈,好主意,不过你加了top bar 说明你有moment there. 如果加宽不多的话,你的
existing footing 外的development 可能就不够了,需要hook,那你就不能穿过那个
洞了。 ACI318 给你的是正常的情况,估计不适合你,你需要的应该是epoxy
embedment. 你的情况edge distance应该不大,要想develop #5然后发挥钢筋全值很
难,concrete governs.非要计算的话,你可以算出钢筋拉力,去HILTI表查,具体还看
edge, spacing distance. 看你的结构重要性决定把。胡言乱语,不对请指正。 |
|
z******i 发帖数: 5114 | 8 一般的基础钢筋都是在底部配的吧,你确定是要加在TOP?
这个最好查HILTI的表格比较容易,按规范计算太复杂 |
|
t******o 发帖数: 467 | 9 你要弄清楚荷载大概在什么范围。如果只是普通的木结构一到两层房子,土壤压力控制
基础设计,钢筋配置一般只是最低配筋,根本没什么必要做develope length。 你只要
大概6‘’epoxy into existing footing. 你可以用Simpson Set Epoxy or Hilti
RE500 Epoxy. |
|
A****F 发帖数: 699 | 10 我这个因为基础没有沉降问题,所以不像动基础,但他的房子太老,没有抗震设施,决
定加宽高出地面的地基-条形基础,然后可以设置和crawl wall 得拉结。 |
|
A****F 发帖数: 699 | 11 是一层木结构,80年旧的房子,原地基是素混凝土的。爬墙和地基间没有联接。80年沉
降已经完成了,所以加固原有地基没有意义,相反可能导致新的沉降,如果从原有地基
地部加固的话。所以只要加宽伸出地面部分地基,进而设置与
墙的连接。 |
|
t******o 发帖数: 467 | 12 Looks like it will be light loaded. #4 or #5 rebar epoxy dowel 6'' into
existing concrete will be fine. By the way, plain concrete is allowed for a
lot of residential construction even in current code at some areas. |
|
A****F 发帖数: 699 | 13 对,我准备用#5 REBAR.我们这里好象没有REBAR拿不到PERMIT
a |
|
J***i 发帖数: 541 | 14 Chemical bonding bolts are expensive. Why don't you just drill a hole and
let the rebars go thru. Just bend the bars into L shape. |
|
A****F 发帖数: 699 | 15 我就是决定转个穿墙的孔算了,BTW, EPOXY并不是很贵。 |
|
|
J***i 发帖数: 541 | 17 谢谢你的包子,epoxy不贵的话,那你在穿墙洞里用点好了,保护钢筋,加强锚固。记
得钻孔的清理,在扩展条基时,扩展部分下部要垫碎石。祝成功! |
|
y****t 发帖数: 17 | 18 P23 chapter1 3.18 (b)怎么做?
Projectively Normal Varieties
A projective variety Y(P^n的子集) is projectively normal (with respect to
the given embending ) if its homogeneous coordinate ring S(Y) is
integrally closed.
(b)let Y be the twisted quartic curve in P^3 given parametrically by
(x,y,z,w)=(t^4,t^3*u,t*u^3,u^4). Then Y is normal but not projectively
normal.
thank you very much! |
|