由买买提看人间百态

topics

全部话题 - 话题: bolt
首页 上页 1 2 3 4 5 6 7 8 9 10 下页 末页 (共10页)
b*****e
发帖数: 5133
1
看样子开始担心你将来的piston AR了:)
这个不一定,主要还是看bolt的设计和加工,AK和SIG 55x bolt的bolt lug数量少个头
大,非常皮实,另外用piston的枪bolt受高温影响不如direct impingement大。bolt
lug的几何外形可以决定受力时间长度和集中程度,一些稍加改进过的AR bolt,如
Leitner Wise bolt,还有Superbolt可以使bolt lug吃力更均衡而延长使用寿命。
想当初piston AR一窝蜂的时候我也想过要来条piston AR,但是多年来piston AR在我
心目中的感觉是越来越差,HK416也不能改变这点(不过我喜欢HK416的firing pin
safety)。如果要short/long stroke gas piston长枪,应该考虑从一开始就是以gas
piston为工作方式而设计的枪。
p*****2
发帖数: 21240
2

Storm能handle多大的数据量就不用解释了吧?不服气的去看看Twitter的流量。
Storm怎么工作的也很简单,不熟悉的看看Nathan的video去。
Storm支持stream和RPC,这个系统可以利用Storm的RPC。接口也很简单,query和book
query和book从spout进去,然后可以根据车次的hash发送到不同的bolt上去。也就是说
同一个车次的query和book会发送到同一个bolt上去。bolt里面保存车次的信息,in
memory。query不用说了,直接返回车次的信息即可。关键是book。book的时候bolt
mark一下,先到先得,后到返回失败。然后把transaction发到下一层bolt中去。下一
个bolt去bank charge,成功就ack这个请求,失败就fail请求,上一级的bolt unmark
,并且返回失败回去。
topology 就是三层
第一层spout,接受query和book
中间一层bolt保存列车信息, respond查询
最后一层管transaction的
log保存在cassandra里。
y***n
发帖数: 2318
3
"the Bolt more for EV enthusiasts won over by practicality and the Model 3
more fore EV converts who want to be part of the Tesla mission or mystique."
- so the stereotype of Tesla buyers are those white liberals.
APARNA NARAYANAN @ IBD
8:21 AM ET
Elon Musk's delivery party for the first 30 Model 3 electric cars over the
weekend saw a fresh burst of headlines about an EV slugfest between Tesla (
TSLA) and General Motors (GM). But there's another one electric vehicle race
that no automaker wants ... 阅读全帖
y***n
发帖数: 2318
4
【 以下文字转载自 Automobile 讨论区 】
发信人: yeson (快乐着并幸福着...), 信区: Automobile
标 题: If You're Not High On The Model 3 Wait List, Get Ready To
发信站: BBS 未名空间站 (Tue Aug 1 10:33:07 2017, 美东)
"the Bolt more for EV enthusiasts won over by practicality and the Model 3
more fore EV converts who want to be part of the Tesla mission or mystique."
- so the stereotype of Tesla buyers are those white liberals.
APARNA NARAYANAN @ IBD
8:21 AM ET
Elon Musk's delivery party for the first 30 Model 3 electric cars over the
... 阅读全帖
s*****i
发帖数: 5548
5
☆─────────────────────────────────────☆
xie91 (bob) 于 (Mon Mar 4 19:12:18 2013, 美东) 提到:
发信人: kylin1996 (kylin), 信区: SanFrancisco
标 题: Re: 再谈德州经验 (转载)
发信站: BBS 未名空间站 (Mon Mar 4 17:16:16 2013, 美东)
看见有人说湾区收入高就笑了,给你们科普一下,猴子屯,13-15w年薪非常普通,20w
以上的一大把,加上公司100% match 6-12% 401k, 公司服务到退休有一次性上百万的
pension,还有一周工作四天一周工作五天,每年5周vacation,加州风景再美,这些能
比吗?
☆─────────────────────────────────────☆
delubo (I shall be your eyes!) 于 (Mon Mar 4 19:13:42 2013, 美东) 提到:
求介绍工作,我要跳槽
☆────────────────────────────... 阅读全帖
q**u
发帖数: 12289
6
来自主题: GunsAndGears版 - 有人喜欢K31步枪吗?
"The K31 is a manually operated, straight bull bolt-action rifle. The
rotating bolt has two opposing lugs at the front, which are locking into
the cuts in the receiver ring. The straight pull bolt handle has a large
T-shaped handle and a stud, which enters the helical groove on the bolt
body. When the bolt handle is retracted, the stud first forces the bolt
to rotate and unlock, and then pulls the bolt back for reloading cycle."
其实跟ak的旋转闭锁原理是一样的。你就想像一把ak,减去导气/活塞部分。
j***n
发帖数: 3786
7
来自主题: GunsAndGears版 - AR-15的可靠性问题
关于AR-15的可靠性问题,我想跟班上的同学阐述一下我的观点
1. 不可靠性的来源:
当过兵的同学可以证实一下,新兵训练营里面最终要一堂课就是怎么清洁自己的武器。
美国也好,中国也好,当兵的没有事情就在擦枪,直到今天美国陆战队的新兵营里也有
连续3天教新兵怎么保养武器。所以合理的保养自己的武器,是所有持枪者应该有的觉
悟。你要想枪拿起来就能扣响,那么你一定要保养的你武器。
60年代, M16开始换装的时候,美军认为这个武器非常先进,基本不需要清洁,开始发
放的时候连基本的保养工具都没有带,所以M16刚刚投入使用的时候故障频频。但是这
个问题很快就被纠正过来,美军专门发放了小册子和保养工具给每个士兵,所以M16又
可以可以得到保养了。这个事件你可以问任何一个越南老兵,他们在巡逻结束之后,必
然开始保养武器。越战后期,M16A1投入使用的时候,M16已经被普遍接受了。很多M16
会出故障的情况,其他武器系统也会出故障。枪膛进沙,进异物,Ak-47,M24,M14都会
卡,不信你自己试试。
2.AR-15的保养
很多同学认为AR-15很难保养,建议大家都是看一下陆军或者陆战队发的保养指... 阅读全帖
q********1
发帖数: 1480
8
来自主题: GunsAndGears版 - 我的刀疤
有人说刀疤能增加男人的雄性气概,这无从考证,但我新得的刀疤(SCAR)-Special
Operations Forces Combat Assault Rifle 确实是个很男人的东西。
一直想买个大口径步枪去打野猪打鹿,对栓动步枪不感兴趣(不过今后还是要买一枝
滴),目标是弄个“栓动的精准和半自动的持续打击力”兼而有之的枪,口径要大。最
初想到的是Browning的BAR 308,但不喜欢枪的样子,加之BAR虽是半自动,但弹匣四发
装弹,”持续打击“的力度太小,放弃。接着关注的AR 308有很多符合外貌控的要求,
打得也准,但整枪重量(还不包括光瞄等零碎)普遍在十磅以上,太重,我可不想背着
这样的枪去钻林子。最后范围集中到DMPS Lite Hunter 308 和Larue Predatar 7.62,
都是不到8磅的重量。 DMPS是很多人推荐的”实惠“枪,但我对其做工和可靠性都存
疑虑,最终拔了草;Predatar 无论从外貌、做工、准确性方面都符合我的要求,决定
要它了,却到处缺货,买新枪唯一的途径似乎就是从厂家定购,等12-18个月还不一定
能买到, 买枪我虽然不急,但这... 阅读全帖
H********g
发帖数: 43926
9
来自主题: Joke版 - 王都统的专利全文找到了
http://en.wikipedia.org/wiki/Captive_bolt_pistol
这工具堪称小杀器
The principle behind captive bolt stunning is a forceful strike on the
forehead using a bolt to induce unconsciousness. The bolt may or may not
destroy part of the brain.
The bolt consists of a heavy rod made of non-rusting alloys, such as
stainless steel. It is held in position inside the barrel of the stunner by
means of rubber washers. The bolt is usually not visible in a stunner in
good condition. The bolt is actuated by a trigger pul... 阅读全帖
l***g
发帖数: 859
10
LONDON — The coach of the Chinese Olympic track cycling team said Friday
that Guo Shuang and Gong Jinjie were “robbed” of a gold medal when they
were disqualified for a rule violation.
Daniel Morelon told The Associated Press that China cannot appeal the
decision in the team sprint final.
0
Comments
Weigh In
Corrections?
Personal Post
Cycling
Home | Results | Schedule
Women's Sprint Quarterfinals - Heat 4
Women's Sprint Quarterfinals - Heat 2
Women's Sprint Quarterfinals - He... 阅读全帖
l**f
发帖数: 56
11
来自主题: Olympics版 - 跳高纪录/朱建华
这个我认为不对, 否则10000米要比100米容易破很多.但其实不是这样. 因为10000米要
求各环节都不能错,也是很难的.楼主说跑得项目比跳得项目容易破,也不对的.
过去50年,
男子跳高世界纪录被刷新了22次左右
男子三级跳 13次
男子100米19次.
男子200米13次
男子10000米20次.
一个稍微例外是男子跳远,过去50年记录变化只有9次, 因为比蒙60年代那惊人一跳. 可
以统计前80年或100年,就会看到统计上这些项目没有明显不同.
从长时间段来看, 成熟的田径项目都是类似难度的(游泳应该没有进入类似稳态,所以记
录破得频繁). 简单讲,都非常难.如果碰到天才型选手,一般纪录都要等一,两代人才能
破,也就说,至少要以decade计. 楼主有类似感觉其实是因为现在短跑上因为Bolt, 所以
显得容易些. 对于短跑而言,因为 bolt, 我们其实处于一个很特殊的时代, 往前看什么
时候百米破纪录以0.1而不是0.01来计算就知道他的特殊了. 类似的, 200米在门内阿的
记录等了17年,才等到Johnson这个怪物,然后他的记录12年后才被bolt破. 跳远比蒙之
后... 阅读全帖
c******k
发帖数: 1089
12
来自主题: Automobile版 - Guide Pin螺栓拧断了,如何取出?
今天安front brake rotor, torque wrench出了点毛病,加上自己也有点累得昏头了,
就把brake caliper上的bolt拧断了。
现在的情况是大概有1/2 inch长的bolt断在跟caliper连接的那个铁板上了,caliper还
是可以取下来的,那个bolt大概有半厘米露在外面。
能不能用C clamp夹住拧下来? 那个bolt应该是16ft-lb,拧断的时候,我估计实际可能
到达25-30ft-lb了。
还有什么工具推荐吗? 能有效夹住那个bolt就可以了。
多谢了!
btw: 现在我的右前轮BRAKE CALIPER是用一个bolt固定住的。
m******n
发帖数: 6327
13
来自主题: Automobile版 - [合集] 换刹车换出问题了
☆─────────────────────────────────────☆
testSystem1 (test system) 于 (Sun Jan 9 17:23:29 2011, 美东) 提到:
今早换刹车,卸轮胎时一个螺丝拧不下来, 后来把金属bolt拧断了(见右下方红箭头
处)。想问大侠的是:
1.要换part的话,那part叫什么名字啊?大概多少刀?
2.买个part,然后自己换可行否?
3.如果去修车行换,part+labor总共大概多少刀?
4.上次是COSTCO rotate轮胎给拧的螺丝,能否找他们算账啊:-)?
多谢了!
☆─────────────────────────────────────☆
tingtingliu (Grand Cherokee Overland) 于 (Sun Jan 9 17:42:33 2011, 美东) 提到:
nug lut bolt
part 5刀
人工估计要 200

☆─────────────────────────────────────☆
DDR3 (UPG) 于 (Sun J... 阅读全帖
z****g
发帖数: 2128
14
来自主题: Automobile版 - Acura/Honda ATF Drain&Fill,含图
继上次的帖子,http://www.mitbbs.com/article_t0/Automobile/33149443.html
这次上点图,带点说明。
步骤:
1)将车子撑起,放jackstand
2)找到drain bolt,用一个3/8"的wrench将其拧开
3)等ATF留干净了,将drain bolt拧回去,用34lbs/ft的力拧紧
4)撑车,拿走jackstand
5)开hood,将fill bolt拧开
6)放funnel(长的),然后3quarts的DW-1喂完,结束。
注意事项:
a) 先break fill bolt。你需要17mm的socket,一个break bar。最好是1/2"的
extension bar。我有3/8"和1/2"的,3/8"的拧起来后,感觉杆子自己都被拧动了。
b) 实在搞不定 fill bolt,你还可以从dip stick那里fill,但是你需要一条接通你
funnel和dip stick口的软管,具体大小你要自己量好了去home depot买。
c) a+b没搞定,千万别drain,免得车子开不了了。
d) drain bolt是需... 阅读全帖
l*********u
发帖数: 19053
15
来自主题: Automobile版 - 看了一下2014 mdx
刚reall
2014 MDX
POWER TRAIN:AUTOMATIC TRANSMISSION
Recall number: 13V571000
Recall date: 11/14/2013
Problem Summary:
AMERICAN HONDA MOTOR CO., INC. (HONDA) IS RECALLING CERTAIN MODEL YEAR 2014
ACURA MDX AWD VEHICLES MANUFACTURED MAY 6, 2013, THROUGH OCTOBER 14, 2013.
THE BOLTS THAT ATTACH THE DRIVE SHAFT TO THE AUTOMATIC TRANSMISSION TRANSFER
ASSEMBLY MAY NOT HAVE BEEN PROPERLY TIGHTENED. AS A RESULT, THE BOLTS COULD
LOOSEN POSSIBLY ALLOWING THE SHAFT TO DETACH.
Consequence:
IF THE DRIVE SHAFT D... 阅读全帖
o****n
发帖数: 1520
16
来自主题: GunsAndGears版 - $399 的12ga 半自动霰弹枪 -- Linberta
某NC枪友买了这个枪:
Yesterday, 11:16 PM
http://www.mdshooters.com/showthread.php?t=89522
Was doing a Google search and found this thread, so registered and now
giving my 2 cents. *
I decided to take a chance and purchase the Linberta 01L semi auto in walnut
for $450 at Buds with free shipping. *It arrived this past Wednesday at my
FFL. *Upon arrival, I opened the box and was immediately hesitant. *The
first thing that hit me was that the picture shows a gloss finish with a
somewhat burl walnut wood. *I ... 阅读全帖
u********r
发帖数: 2525
17
来自主题: Outdoors版 - 有啥经典的登山电影吗
哦,呵呵,至少明白了三个人干嘛
那老爸谁belay的?肯定是老爸爬的时候只是老爸爬,不能一个人lead belay俩吧
那他们是从同样的belay station出来的,老爸让儿子检查什么意思?
老爸没看见那个belay的anchor?
老爸在一个两个bolt的Anchor弄好belay居然儿子都爬了三分之二了
老爸太业余了吧(当然老爸现订了那两个bolt除非),或者路线简单
这么简单的话,等一下老爸一下belay两个不就完了
他们这样能省多少时间?而且那老爸还没开始给belay,上面那根绳子怎么收的呢?
老爸开始给儿子top belay的话,女儿怎么办?等着?
还要等到儿子上去了,两个人等着女儿爬,综合时间一点不节省比起老爸belay两个来
混合路线那个我接受解释
bolt呵呵电影是在太胡扯了,两个人如何能拔出N个bolt,唯一的解释是
那些Sand stone里面用的老款Bolt,豆腐渣工程。冲到他老爸那里的时候,力道大的可以
拔出那两个anchor bolt,但是完全被他老爸的身体给救住了,老爸钢做的
头盔chris sharma,alex他们确实不戴头盔,那时他们在一个proj... 阅读全帖
c******g
发帖数: 19294
18
来自主题: Paint_ball版 - How does paintball gun work
spyder is one of the most famous manufacturers of paintball gun, also known
for the open bolt design. Bolt is a moving part in the gun and it pushes the
paintball to the position where it will be fired by compressed air source (
could be N2, Air, or CO2). By open bolt, it means the bolt is in the rear
position to where the paintball is fed. When triggerd, the bolt is driven
forward by a spring and push the paintball to a position where compressed
air is released, hence the paintball is fired.
G... 阅读全帖
c******g
发帖数: 19294
19
来自主题: Paint_ball版 - Re: 给beginner的建议
【 以下文字转载自 paintball 俱乐部 】
发信人: cengceng (路色), 信区: paintball
标 题: Re: 给beginner的建议
发信站: BBS 未名空间站 (Mon Jun 14 01:33:00 2010, 美东)
接着该说说彩弹枪了。
彩弹枪大体分两种,机械的和电子的。所谓机械和电子都是指得扳机的触发方式。机械
触发射速较慢,但是好处是不怕进水。电子触发射速更快,高端的电子彩弹枪可以达到
30+bps,但是下雨天的时候最好还是小心使用,免得把心爱的彩弹枪电路烧了。此外还
有一种叫做pump paintball gun,不知道咋翻译。不同之处在于每打一枪,都需要手动
pump一下。而机械触发彩弹枪属于半自动,不需要拉枪栓。电子彩弹枪可以选择半自动
或全自动,全自动就是扣着扳机就不停的发射,我个人感觉相当烧钱,而且在大多数
paintball field里,或者正式比赛中不允许全自动模式。
彩弹枪价格从几十到上千不等,对于刚开始上手的同学,我觉得spyder和tippmann的低
端枪比较合适。一个是价格不高,100左右。二来性能稳定,属于彩弹枪... 阅读全帖
w*******y
发帖数: 60932
20
this is a great deal for a superb complete bolt carrier group for your 223/5
.56 AR15 build. 129.95 shipped from AIM surplus.
from the website:
"New Daniel Defense Bolt Carrier Group. Complete with Bolt Carrier, Bolt and
Firing Pin. These High Quality Bolt Carrier Groups are all HPT & MP Tested,
Chrome Lined, Military Spec. Heavy Phosphate Coated, and feature a properly
staked gas key. BCGs are machined from Carpenter 158 Steel. Gas Keys are
also hardened. "
DD parts are good to go!
Link:
http:... 阅读全帖
h***y
发帖数: 4936
21
Olympics boss Jacques Rogge jumps into sprinter feud saying Usain Bolt not
yet a legend like American great Carl Lewis
LONDON – A spat has broken out among the world's two most famous living
sprinters, spawning a second argument between IOC president Jacques Rogge
and London Olympics head Sebastian Coe.
The trouble began when Rogge, speaking to reporters before Usain Bolt's 200-
meter victory on Thursday, said he didn't think Bolt was yet a legend like
Carl Lewis, the Willingboro, N.J., sprinter... 阅读全帖
m*****y
发帖数: 7
22
前段时间开上curb,把下面右边撞坏了,包括
control arm, ball joint, CV shaft。考试前
拆了一次,control arm的最后一个bolt拔不出来。
考试完了准备接着弄。周五室友开车去junk yard买回了这
些部件,今天天气还好,就是风有点大,就开工了。
分析了一下,主要是因为撞歪了,那些bolt都变形
了,被卡住了。因此就试着加外力让那些部件尽量
回到原位置。为此还去借了clamp,可惜最后没有用上。
后来就直接把jack放在control arm的下面,用jack
加力,非常有用,一边加力,一边试着往外拧那个
bolt,发现在某个位置用手都可以弄动,然后就顺利
取下来。
现在所有的螺母都取下来了,可是整个control arm
还是下不来,原因仍然是部件变形,有两个地方
完全卡死了。看了一下,决定锯掉连接后面的一个
类似bolt的东西。先用电转试了一下,地方太窄,伸
不进去。只好用手慢慢锯了,为此还去买了新锯条。
旁边就有一家ACE hardware,比较方便。里面的服务
人员还帮着推荐了一把,原来不同的材料需要不同
的锯条,据bolt之类的金
t**l
发帖数: 577
23
上贴说过,timing 虽然随时都可以重设,如果是自己第一次做,最简单的就是在拆出
旧的TB前counterclockwise转crankpulley,把Timing设到No1 piston d TDC,对于
accord,这里有4个pulley:
1. Camshaft pulley的 “UP" Mark 需要正上 --- 这个跟crank pulley 的timing
mark匹配 (照片1)
2. crank pulley TDC mark要align到oil pump上的Mark (照片2)
3. Left front balancer pulley (照片3)
4. Right front balancer pulley (照片4)
然后就是松开tensioner Bolt后,把里面那个tensioner往下压(照片5),外面那个往
上推(照片6),两条带就一起松下来了--- 这个其实看一下就明白朝那个方向推了,
因为反方向只能让belts更紧
记得换WP前要先放掉coolant,否则水漫金山!换WP就没啥说的了,感觉看不看手册都
无所谓,拧螺丝不要太松或者太紧就好。
个人从... 阅读全帖
c*********n
发帖数: 1057
24
来自主题: JobHunting版 - 问个sorting的题目
对的就是这个思路,可能我题目没说清楚吧,
n个nuts, n个bolts
每个nut都可以找到一个对应的bolt
nut之间不能比较,nut只能和bolt比,看是否能放如bolt,是否bolt比nut大
w********s
发帖数: 11
25
来自主题: JobHunting版 - 几道老题 的解答
第3题有点奇怪,如果所有的nuts对所有的bolts都是大(无法定量比较大多少),则没
法排序呀。
类似的只见过n个nuts和n个对应的bolts的,每一对规格大小不同。这种情况可以就用
quick sort的思路,先用一个nut做pivot对bolts做一轮quick sort,找到配对的bolt
后,用这个bolt再对nuts做一轮quick sort...... 相当于两个数组交错进行quick
sort。
w********s
发帖数: 11
26
来自主题: JobHunting版 - 几道老题 的解答
第3题有点奇怪,如果所有的nuts对所有的bolts都是大(无法定量比较大多少),则没
法排序呀。
类似的只见过n个nuts和n个对应的bolts的,每一对规格大小不同。这种情况可以就用
quick sort的思路,先用一个nut做pivot对bolts做一轮quick sort,找到配对的bolt
后,用这个bolt再对nuts做一轮quick sort...... 相当于两个数组交错进行quick
sort。
i**X
发帖数: 156
27
bolt都能断肯定是质量问题, 这句话不对。 如果安装不按规范作,bolt很容易断的。
拧不进去,硬
拧,结果就是bolt折断。 经常是螺纹没有对好, 用力方向不对等等。 很多人蛮干的
,弄断了还不负
责任,只想一退了之。 Home Depot 有特殊的bolt, 不容易拧断。但是家具里一般不用
这样的
bolt。
美国的顾客都惯坏了。 买东西的时候一味追求便宜,用的时候又要求高质量。久而久
之,市场的退货规
则都被迫改变了。现在你去商店,退货就不象十年前那么容易了。
b*****9
发帖数: 8922
28
☆─────────────────────────────────────☆
bolt (地球上跑的最快的人) 于 (Mon Aug 30 22:39:30 2010, 美东) 提到:
发信人: bolt (地球上跑的最快的人), 信区: BackHome
标 题: 父母绿卡美国出生的2岁半小孩可以申请2年多次中国签证吗?
发信站: BBS 未名空间站 (Mon Aug 30 22:28:05 2010, 美东)
申请表上只有一年多次往返。
不知道能否申请到两年多次往返?
哪位大虾有经验?
谢谢!
2个包子答谢!
☆─────────────────────────────────────☆
benchmark (maine) 于 (Mon Aug 30 22:39:52 2010, 美东) 提到:
第一次不可以。
☆─────────────────────────────────────☆
bolt (地球上跑的最快的人) 于 (Mon Aug 30 22:42:04 2010, 美东) 提到:
第二次以后就能申请2年多次往返了吗?
☆──────... 阅读全帖
m*****g
发帖数: 12253
29
☆─────────────────────────────────────☆
visit (Just beat it, beat it) 于 (Sun Jan 22 19:10:21 2012, 美东) 提到:
能满分么?
☆─────────────────────────────────────☆
mitbbsindc (谁人不识君) 于 (Sun Jan 22 21:27:50 2012, 美东) 提到:
没戏。
☆─────────────────────────────────────☆
TodayEscape (路客西) 于 (Sun Jan 22 21:49:30 2012, 美东) 提到:
10岁的时候还有可能
☆─────────────────────────────────────☆
lqm1989 (老球迷) 于 (Mon Jan 23 10:11:51 2012, 美东) 提到:
从来都没有可能
☆─────────────────────────────────────☆
NKlaker (laker) 于 ... 阅读全帖
S****r
发帖数: 982
30
来自主题: GunsAndGears版 - 想弄一支打猎的步枪
Long Range Hunting Rifles (any type)
* Kimber 84M LongMaster Classic (bolt)
* Remington Model 700 VLS, 700 Sendero SF (bolt)
* Ruger No. 1B and K1-B-BBZ (falling block)
* Savage Model 12FV/12FVSS (bolt)
* Weatherby Mark V Accumark (bolt)
* Weatherby Vanguard Sub-MOA, Sub-MOA Stainless (bolt)
f****a
发帖数: 4708
31
来自主题: GunsAndGears版 - WSJ报道remington 700有潜在质量问题
misfire是死火,unintended fire是走火。
走火的主要问题是子弹如果没有上膛,在receiver里被击发了,就会伤到射手。有这样
的官司,说是在装弹的时候走火。
检查bolt action的safety的方法:
"The next step in adjusting a trigger is the most important – ensuring
safety. I run through several tests, the most basic of which is cocking the
action by lifting and closing the bolt. If the action does not stay cocked
when cocking the action very quickly, the trigger pull is too light. If
the action passes this test, I then lift the bolt, pull it back to the rear,
and slam it... 阅读全帖
f*********n
发帖数: 11154
32
由于是猎枪,整个枪支不重;托在手中以及上肩,总体的平衡性能很好。枪管从外表上
看和其他类似的型号没有区别;内部是5条来复线。枪管是自由浮动。在靶场归零时,
打了11发子弹后枪管很烫,必须得等到温度降下来以后才能继续打。
Venture的bolt设计和A-bolt都采用了60度旋转,打开和合拢都非常顺当,尤其在清理
干净并且上了润滑油以后。这个bolt而且向后偏了一些,而不是直直的伸出来,对于开
关也很有帮助。
唯一需要抱怨的,是bolt的release hatch,需要用拇指向里面按进去,而且用的力量
比较大,拇指骨容易刺痛;一次不成功,第二次就困难很多。
说明书中明确说可以dry-fire,所以在家里试过几次。扳机非常的脆,行程很短,基本
上食指发力就可以触发。将bolt取下以后有一个可以调整扳机力度的孔。出厂时的力度
对我来说有点太轻,所以把力度加大了一些。
弹匣是可以容纳3发子弹,用塑料做的,使用寿命如何,也只有在以后的日子才能知道。
光瞄采用的是在midwayusa购买的Simmons Whitetail Classic,6.5-20倍,50mm物镜,
Truplex Reti... 阅读全帖
f*********n
发帖数: 11154
33
比去年12月份同样的upper贵了20块钱。加个MBUS和lower,就可以上靶场了。
http://www.surplusammo.com/products/DPMS-Panther-A3-Lite%252d16
DPMS Panther A3 Lite-16 Complete Upper Receiver Assembly- 5.56 NATO
This 16" DPMS Panther Lite weight upper receiver offers the quality &
accuracy DPMS is known for as well as it's refined many great features &
light profile barrel that won't weight you down. This upper receiver is
complete, ready to shoot; just mount to any AR-15 lower receiver. Great
for target shooting, officers, or an... 阅读全帖
f****a
发帖数: 4708
34
寿命都是和精度一起看的。
比如原来精度是2MOA,打了一万发后还是2MOA,那么寿命至少有一万发。
chrome lined的AR15的枪管寿命一般是最少7000发,一般在一万发以上。
auto dump会加快精度的降低。
以前看到美军的一个报告,bolt是M4常见的第一个会坏的部件,
http://www.dtic.mil/ndia/2006smallarms/taylor.pdf
"Most bolts subjected to harsh firing schedules will show initial cracking
around 3,000 to 6,000 rounds"
"On milder schedules, nearly all bolts will show initial cracking at 6,000
to 10,000 rounds"
"Once the crack is initiated, the bolt may fail at any time, or may last for
thousands of rounds, depending ... 阅读全帖
k*******n
发帖数: 5546
35
刚刚看了个视频演示,Magpul S.P.O.R.T和处理AR15 double feed, 演示的是右手持枪
的,左手持枪是不是这样,大家别光研究装备,都来指导一下啦:
普通的AR15 lower,非Ambi的,没用BAD:
方法1)左手握Pistol Grip:
判断Double feed
左手拉charging handle 同时右手伸到另一面 食指和中指锁住bolt
左手握好枪
右手拇指按mag release 大力拉出弹夹
左手握枪小幅偏向右侧
右手反复拉charging handle直到看到抛弹
右手上新弹夹
右手拉charging handle上膛,继续射击
方法2)左手握Pistol grip:
判断Double feed
左手前伸 左手拇指锁住bolt(手指够长也可以直接用食指)右手拉charging handle
左手回来握好枪
右手拇指按mag release 大力拉出弹夹
左手握枪小幅偏向右侧
右手反复拉charging handle直到看到抛弹
右手上新弹夹
右手拉charging handle上膛,继续射击
我觉得处理double feed不能光图快和省... 阅读全帖
S**********s
发帖数: 4534
36
比SCAR 17S重两磅, 还贵1000多。 慢走不送。
P.S: 附上一篇老段子
http://larrycorreia.wordpress.com/2007/10/09/hk-because-you-suc
"An open letter to the gun community from HK’s marketing department: In a
world of compromises, some people put the bullets in the magazine backwards
…But it doesn’t matter, because our gun is on the cover of the Rainbow Six
video games. Look how cool that SEAL coming out of the water looks… If you
buy a $2,000 SOCOM, you will be that cool of an operator too. And chicks
will dig you.
At HK, ... 阅读全帖
a***a
发帖数: 8941
37
来自主题: GunsAndGears版 - 求建议:17HMR的步枪
一直想搞一把17HMR的步枪,但是一直有些犹豫。
我想搞一把重管栓式的。因为17HMR的子弹比较贵,也希望枪的精度比较高。
现在有3个候选对象:
1)Savage 93R17FVSS 重管不锈钢,重量6磅,价格320刀:
http://www.budsgunshop.com/catalog/product_info.php/cPath/62_97
2)CZ-452 varmint, 6.84磅,价格463刀:
http://www.budsgunshop.com/catalog/product_info.php/cPath/972/p
3)Browning T-bolt varmint,直拉枪栓,5.12磅,价格651刀
http://www.budsgunshop.com/catalog/product_info.php/cPath/58_12
我个人和LP都喜欢T-bolt,这个枪的设计我比较喜欢,直拉枪栓很方便,还有双螺旋
弹夹,10发容量,也不错。另外T-bolt在这三把枪里面也是最轻的,扛出去打猎也比较
方便。
但是不知道T-bolt的精度如何,以前有qbq网友说他手上的T-... 阅读全帖
h*********2
发帖数: 2508
38
来自主题: GunsAndGears版 - Gun Board Classic
有点长,但是挺好玩
After some years now of reading internet bulletin boards, I think I’ve got
the pros and cons of possible SHTF rifle choices figured out. Correct me if
I’m wrong, but the following is my analysis based upon the wisdom of
numerous gun board gurus (you know them, they’re always the first ones to
tell you a particular model gun is “junk” and enlighten you as to why they
have made the only logical purchases)…
The AR 15:
Great, awesome, unbelievable rifle(when it works). Can hit a fly in the... 阅读全帖
k*****u
发帖数: 578
39
来自主题: GunsAndGears版 - 新买的ak一发没打 就是打不响
一个比较好的检查办法就是把dust cover拿掉,上膛后看看撞针是否从bolt里面向后移
动出来,bolt和在chamber里面的子弹是否完全紧密的顶住并且紧紧地贴住barrel尾部
,扣扳机的时候扳机是否有力的撞击撞针。我原来那只IO AK74就是recoil spring比较
弱,结果导致虽然子弹能上膛,但是bolt并没有把子弹完全顶死固定在bolt上,所以撞
针根本就没有后移,就算扣扳机扳机也撞不到撞针,而是只撞在bolt的外围。
k*****u
发帖数: 578
40
来自主题: GunsAndGears版 - 新买的ak一发没打 就是打不响
一个比较好的检查办法就是把dust cover拿掉,上膛后看看撞针是否从bolt里面向后移
动出来,bolt和在chamber里面的子弹是否完全紧密的顶住并且紧紧地贴住barrel尾部
,扣扳机的时候扳机是否有力的撞击撞针。我原来那只IO AK74就是recoil spring比较
弱,结果导致虽然子弹能上膛,但是bolt并没有把子弹完全顶死固定在bolt上,所以撞
针根本就没有后移,就算扣扳机扳机也撞不到撞针,而是只撞在bolt的外围。
s******n
发帖数: 6
41
来自主题: GunsAndGears版 - 帮忙选把 .22步枪
最近想买把点22LR,先练铁瞄,再学用镜子。预算200。
1. Marlin 795, 139.99 in academy
2. Marlin XT22 .22LR bolt-action 179.99 in academy
3. Savage Mark II F. 22LR Bolt 179.99 in academy
4. Remington 597 159.99 in Cabela,
5。Savage Mark II FSS bolt 279.99 in Cabela
6. Marlin XT22 HDWD bolt 199.99 in Cabela.
请问2和6有什么区别,3和5有什么区别?
现在倾向于Bolt action,不知道老拉枪栓会烦么?
另外已经有了Remington 870, 不大想再买同一牌子的
不喜欢Ruger 10/22的扳机,觉得太重了。
m*****u
发帖数: 277
42
来自主题: GunsAndGears版 - 问大家一个ar15的问题
今天在大家的推荐下买了人生第一把ar,dicks的troy defense carbine.
因为从来没有射过ar,所以有些问题想问大家。
1. 射击的过程是先不装弹夹,拉bolt到位置以后再装弹夹,然后再拉bolt然后就可以
射击了么?
2. 我没有装弹夹的时候,拉bolt可以回位,不知道为什么装了弹夹之后,拉bolt无法
回位? 研究了一下好像是弹夹里面的那个塑料部件阻止了bolt复位,请问这是正常的么?
★ 发自iPhone App: ChineseWeb 7.7
w*****o
发帖数: 1806
43
原来关键是:虽然都是milled receiver的AK,但是SLR是单排的整枪进口的,然后拆了
,切了,换了不少部件,改成支持双排弹夹,所以是个convert了的整枪;而SAM7是从
开始就造的double stack,所有部件都是新的,所以是个真正意义上全新的枪。
所以价差主要是两地labor的差别。2003年sam7就比SLR101卖的贵个150块左右。
http://www.ar15.com/archive/topic.html?b=4&f=64&t=58578
正像这里那位SSR-99兄说的,这两把枪还是兄弟,就是出生地不同,这个200的价差这
样说起来可能也算合理.
It's correct that for Arsenal Inc to make an SLR-101 into a double stack mag
shooter, they must put the SLR-101 through a conversion process. The SLR-
101 single stack gun arrives completely manufactured and... 阅读全帖
f********r
发帖数: 3155
44
来自主题: GunsAndGears版 - 新Tikka T3 Lite, 30-06,$340, 值得买么?
如果你把Chuck Hawks当作gun god,你应该看看Chuck Hawks怎么贬Tikka T3的,这里
以前讨论过,哈哈
http://www.thehighroad.org/archive/index.php/t-211246.html
A Critical Look at the Tikka T3
(And Other Economy Hunting Rifles)
By Chuck Hawks
Like many old geezers, I bemoan the loss, or lack, of standards in our
modern world. And nowhere is this devaluation of quality more evident than
in 21st Century hunting rifles. (Actually, the slide started in the 1960's
and accelerated toward the end of the 20th Century).
We are, today, reap... 阅读全帖
c*******r
发帖数: 593
45
来自主题: GunsAndGears版 - sig M400如何?
(ZT)
http://www.ar15.com/forums/t_3_118/584620_.html
"I have both. The Sig M400 compares nicely to the LE6920. Here's how they
stack up.
Both have an F marked front sight base.
Both have M4 feed ramps cut before anodizing.
Both have chromed chamber and bores.
Both have equal staking on the gas key and castle nut.
Colt has an M16 bolt carrier.
Sig has an enhanced AR15 bolt carrier.
Colt bolt is MP marked.
Sig bolt is not MP marked although Sig states their supplier MP tests all
bolts, whether the... 阅读全帖
j*****v
发帖数: 7717
46
http://www.akfiles.com/forums/showthread.php?t=171921
核实了一下,buds这款的确是第一代nap,除了rail的问题,bolt是single stack bolt,
这个对稳定性有影响,据说很多卡弹的。换这个bolt要花60刀。
我和团购那家谈判的时候,一再和卖家确定是double stack bolt.请各位拿到手的
时候务必仔细确认。
这是两种bolt对比,double的下面宽点
http://t3.gstatic.com/images?q=tbn:ANd9GcSgsfbtCh7jEU5yMYQJmk4v
w******x
发帖数: 4396
47
来自主题: GunsAndGears版 - Ruger mini 14 stainless
转自perfect union forum
Firing pins for example have to be fitted to the bolt! WHY? The answer is
simple, cuz the bolts are all different. Not because they are poorly
machined, but because they are of different size. Ya see, Ruger doesn't take
the time to set the proper headspace when indexing the barrel. Instead they
mount the barrel and then set the headspace with the bolt. This requires
several different sized bolt. That's right, the bolts on the Mini have an
index number on them and that is fo... 阅读全帖
w******x
发帖数: 4396
48
来自主题: GunsAndGears版 - Ruger mini 14 stainless
转自perfect union forum
Firing pins for example have to be fitted to the bolt! WHY? The answer is
simple, cuz the bolts are all different. Not because they are poorly
machined, but because they are of different size. Ya see, Ruger doesn't take
the time to set the proper headspace when indexing the barrel. Instead they
mount the barrel and then set the headspace with the bolt. This requires
several different sized bolt. That's right, the bolts on the Mini have an
index number on them and that is fo... 阅读全帖
首页 上页 1 2 3 4 5 6 7 8 9 10 下页 末页 (共10页)