H******7
发帖数: 34403 | 1 换地板和（不是或）baseboard (trim,molding). |
|
e********t
发帖数: 9607 | 2 现在harbor freight和floor and decor outlet都有$150左右的flooring nailer卖。
买比租合适。
brad nailer是用来订baseboard。
开始和最后几排需要用8d的finishing nail手动钉。 |
|
h******2
发帖数: 102 | 3 I used finish nailer to do first and last rows (face nailing).
I blind-nailed by finish nailer the rest of rows where air nailer can not be
used. Yhis way you only have nail holes on 2 rows (1st and last rows).
For wide baseboards, brad nails are normally too samll and too short. Finish
nails are better in my opinions (2' long). You really want to nail into
studs not into drywall. |
|
T*********e
发帖数: 9208 | 4 咳咳,我拿pry bar都不容易撬出来，怎么就轻轻一拉出来了
再说你怎么拉baseboard, 难道事先还留个把在上面？ |
|
z*********n
发帖数: 94654 | 5 drywall上订东西当然就是虚的了，不过对baseboard也足够了，我都没用stud，我只是
说教程里这么说而已，找到stud，地上贴条记住位置，在相应位置订
pry bar不好弄，太粗大，用putty knife先break caulk，然后先小心往出拉，拉出一
个缝后就很容易拉出来了 |
|
T*********e
发帖数: 9208 | 6 那还是站着找，你找好之后还要画垂直线到地板。
你如果按这个方法装baseboard,你掐表算一下，至少20-30分钟找stud
一个200sqft的房间，没一小时搞不完 |
|
e********t
发帖数: 9607 | 7 晕，还画垂直线，直接就在baseboard上边1-2寸地方找，下边用nailer立马就钉。
而且一般从插座开始找，16寸一个，用stud finder刷一下确认，钉。钉完stud后再在
stud之间补个钉，我不觉得会多花很多时间。
不过随便吧，个人有个人做事的方式。 |
|
T*********e
发帖数: 9208 | 8 一只手就能找到stud? 你的stud finder这么神奇？
我这个finder要一个手单向移动，找到一个边，再反响移动，找到另外一个边，再找中
线，然后测根前面一个stud的距离，如果不是12或者16"那就有问题，哪有那么好找的,
stud finder有时隔老远就亮了
你不确定准确地中线，你怎么把nail打进2"宽的stud? 我估计你这样打偏一大部分。
老三你别不服气，你看那些contractor哪个望stud打的？你听说谁家的baseboard松了的
against
are |
|
T*********e
发帖数: 9208 | 9 我老比较慢，一个房间至少半小时，还是站着找的。墙上如果有纹理更难找，蹲下去趴
着找也要多花时间。baseboard这个东西根本不可能松动，因为没有东西能拉它，而且1
ft左右还定2个钉子。 |
|
T*********e
发帖数: 9208 | 10 说法可能有，一个project你想做多复杂都可以，不过没必要的东西你干吗要去做，而且
很费事。base board本来5分钟的事情，你让别人花1小时搞？
你装的baseboard松了吗？LOL |
|
T*********e
发帖数: 9208 | 11 哪有那么夸张,我没这么干过,不过你就是把全部baseboard都sand一遍，刷prime, 刷漆
，要多长时间？半小时？跟你16ft刷一个有多大区别？ |
|
K******S
发帖数: 10109 | 12 what I did was to make a mark with a nail on baseboard. Then just fire at
that position. |
|
z*********n
发帖数: 94654 | 13 所以订baseboard不要用太长的钉子，水管也没那么贴近dry wall
真正危险的是钻pilot hole |
|
z***y
发帖数: 473 | 14 你如果没有实际做过，还是不要误导别人的好。尤其是自己DIY, 要让活看起来好一点,
fill/sand/caulk/prime/paint/clean是最花时间的. 订baseboard一定要订到stud上,
因为没有一面墙是完全平整的, 只有靠stud的力量才能hold住板子, 打在drywall上根
本就没用.
个？
、 |
|
H****H
发帖数: 11039 | 15 我刚钉了baseboard，用的是 1 1/2 英寸 16 gauge的unfinished nail。18 gauge的太
细了点儿。
我最终选了气动nailer，air compressor插电源打开开关就会充气。
施？ |
|
|
h******2
发帖数: 102 | 17 it can not miter cut long boards.
I used table saw to cut 12' baseboards because I did not want to buy a miter
saw but it was difficult, inaccurate,and dangerous( You can not move the
long boards when the blade is doing its work). |
|
h******2
发帖数: 102 | 18 Sorry 路客西. But you sure like to offer opinions on things you really do
not know well. On a table saw, how can you push a really long board if you
want to miter cut it? that is the job for a miter saw (you fix the board and
move the blade to miter cut it).
I actually did use table saw to cut 12' baseboards for miter and bevel cuts.
But the results were not good because it was very hard to push the long
boards through the blade and extremely dangerous.
do not get offended but I know many rookies l... 阅读全帖 |
|
h******2
发帖数: 102 | 19 this is for 胡core: since you will use your old baseboards after hardwood
floor is done, you do not need a mitersaw. All you need is a table saw with
miter cut guild.
Many thanks for your Baozi. I just saw them. BTW, what can I do with Baozi? |
|
h******2
发帖数: 102 | 20 table saw with miter cut is a must for hardwood floor. But
if you want to replace old baseboards with new ones, it is good to have a
miter saw as well.
If you are good at circular saw, it it enough for hardwood floor DIY. But
you must be really good at circular saw (know how to rip cut straight long
boards) in a safe way (it is more dangerous for a new DIYer than a table saw
in my opinion). |
|
h******2
发帖数: 102 | 21 we are talking about baseboards as long as 12', not 2 M lumber. 2 M is fine
of course. Now you got it? |
|
h******2
发帖数: 102 | 22 There are many cases where you can not leave 1-2' to hold the lumber. For
example, you need to miter cut the end of long baseboards |
|
x5
发帖数: 27871 | 23 墙宽大于12ft，你从墙角开始钉的第一片baseboard是不是整片都得用上？那是不是两
头都得miter cut?
miter saw固定一边就好了，仅头切
with
很快 |
|
h******2
发帖数: 102 | 24 with a 12' baseboard it is still difficult to 平push even you cut away 1 ft
from the end. |
|
H******7
发帖数: 34403 | 25 这个人为什么不用撬baseboard? 压住地板的Molding是必须的吗？为什么不先上漆再安
装？ |
|
x5
发帖数: 27871 | 26 重装baseboard工作量就要大不少，用quarter round压着也行
quarter round可以在装之前prime，刷漆还得装完，patch hole，sand, touch-up以后 |
|
H******7
发帖数: 34403 | 27 请展开说说：地板肯定不能顶着墙
意指要么撬baseboard, 无moldling, 要么不撬BB，加装M? |
|
T*********e
发帖数: 9208 | 28 用原来的baseboard多简单，起出来的时候留着钉子，到时候按回去就好了。她有的qua
ter round装了个半截，很丑 |
|
h*******s
发帖数: 3932 | 29 不是把baseboard先揭掉，然后订回去？弄个小圆角貌似不好看。 |
|
h*******s
发帖数: 3932 | 30 baseboard下面要留空间防止热胀冷缩的. |
|
j***u
发帖数: 142 | 31 baseboard的暖气系统，是墙里的水管漏水呢？还是正常的热胀冷缩？谢谢！ |
|
h********8
发帖数: 7355 | 32
深有同感。 我用circular saw切的， 经常还得用木挫。用putty极难看， 因为
baseboard和quarter round用oak，没刷油漆。 |
|
j***u
发帖数: 142 | 33 是矮矮的围房间一周的baseboard用的暖气片。 |
|
z*********n
发帖数: 94654 | 34 压缩机，直到不久前走音响线拆卸baseboard第一次用 |
|
j***b
发帖数: 5901 | 35 用红外温度计测量baseboard trim，温度比其他地方低很多。不知道这个要怎么处理。
在此把我的一点冬季房屋保暖的个人经验与大家分享。希望能够抛砖引玉，也希望大家
批评指正。
Fiberglass insulation和Expansion foam。在其他时候保护自己不被灰尘粗糙的表面
伤害也很重要。一下是常用的防护工具：
毕竟是自己的肺，进入杂质很不舒服而且难清除）。 |
|
j***b
发帖数: 5901 | 36 我的是slab地基。我把一个房间地毯揭起来，用一张硬纸片插进去，发现可以穿过dry
wall到外面。
现在我想用caulk堵一下。可是有不想重新弄trim和baseboard。犹豫中。 |
|
f****i
发帖数: 20252 | 37 很成geothermal的heat pump？ |
|
|
f****i
发帖数: 20252 | 39 或者弄个外循环煤气壁炉，如果壁炉位置在房子中心的话 |
|
|
|
m***y
发帖数: 14763 | 42 Nod
Heat pump works by sucking energy from ambient air/soil. The conventional
ones start losing their efficiency when it's below 47°F, and have to fall
back on electric heating, which got low efficiency than gas/oil heating.
Good news is that newer heat pumps can be optimized for low temperature and
keep their full capacity as low as 14 °F. I figure, the moral is, don't
replace it if it ain't broken, because the better are always coming. |
|
m***y
发帖数: 14763 | 43 Essentially, it's 暖气片 with casement. Could be steam, forced hot water,
electric resistance or convection. |
|
m***y
发帖数: 14763 | 44 Agree, geothermal might work in NJ. But in New England, the frost line is at
least 4', costs too much to dig so deep. |
|
|
h********8
发帖数: 7355 | 46 墙颜色跟laminate很配。
baseboard应该铺完才钉吧。。。 |
|
j***b
发帖数: 5901 | 47 单靠这些信息很难知道什么问题。有可能是heater undersize了，也有可能是哪里坏了
，或者房子漏气，insulation不好。反正一切皆有可能。建议你先看看供暖系统。应该
是那种baseboard heater吧，先摸摸看看开起来是暖气片够不够热。 |
|
j*****7
发帖数: 4348 | 48 先装地板, no brainer.
要不然baseboard molding又得重新撬了装地板. |
|
l***e
发帖数: 1121 | 49 这么理解各位大侠对不对：
拆地板，主要是为了拆baseboard molding
刷墙
再装地板 |
|
m*****m
发帖数: 242 | 50 取暖：Forced Hot Air 跟 hot water baseboard， 哪个好些？
取暖效率哪个好些？ Forced Hot Air 会不会有点噪声， 更干些呢？
谢谢 |
|
